A gas fireplace is a typically common fireplace, one that has been in use for quite some time and is still in use, even after the advent of modern and innovative techniques like smokeless fireplaces and electric heaters.
It has a great heat transfer rate and keeps the room warm and cozy while keeping cold drafts at bay. It is a safe, energy-efficient, and environmentally friendly alternative to a wood-burning fireplace, and consumes few natural resources. It is compatible with most homes, and a gas connection is known to increase a home’s resale value.
It doesn’t take much to install a gas fireplace in your home if you are handy with the toolbox and have a general knowledge of construction, but in case you don’t then it would be best to hire a professional to do this job. for you.
In this article, we will discuss how to install a gas fireplace in your home in relatively easy steps. Visit the Magikflame.com website to learn more about these exciting brands of electric fireplaces.
1. An adequate ventilation system
A gas fireplace can be a forerunner in the modern construction industry, and its perfect application in any interior may seem like a coherent amalgam, but it needs proper installation and accessories to deliver the incredible performance it is known for.
A gas fireplace comes with attached parts that must be assembled and connected to the integral parts of your home, such as the fireplace.
Because the gas fireplace runs on natural gas, it needs a proper ventilation system, and for that system to have an outlet, it must be connected to a narrow chimney exhaust. If you have no experience working in construction, be aware that you may do more harm than good.
To install a direct-vented fireplace, the intake and exhaust vent combination must pass directly through the exterior wall. Then you need to properly texture the drywall and create a suitable environment so that it is not combustible. All of that can cost you roughly $ 2000.
2. Mechanical requirements
Aesthetics are important when designing a fireplace, but installing it is a completely different experience. First and foremost, you should have a gas supply line for your fireplace, and you definitely need to call a plumber for that, and you don’t necessarily need an electrical connection, but if you want to install a blower, then you must need to run an electrical cable. to the circuit, to get that connection.
Next, you need to determine how to get the vents from the fireplace location to the outside. It must have perfect clearances and placement patterns, and because the pipe comes in a double-layered formation that prevents heating and provides adequate insulation, it can go through the wall or ceiling. Other than that, you must have legroom for all your allotted space assignments; you can get them in the instruction manual.
3. Design a platform
Once all the initial preparations have been made, you need to order all the parts and wait for the plumber and electrician. In the meantime, you can choose a design for the location of the fireplace and start building a platform. That platform would have to be covered with drywall and be properly glued and decorated. If you want to install a gas fireplace, you can do no better than look for the best commercial plumbers Melbourne has many of.
4. The hole in the wall
Once the deck has been built and configured, you would have to connect it to the vent, which would then go through the wall. However, to connect the ventilation, you would have to cut a hole in the wall; make sure the cuts are shallow while using the saw or you could end up disconnecting the hidden cables.
The hole would have to be 1’x1 ‘. Since various houses are made up of different materials, you may have varying degrees of difficulty cutting this hole.
After the hole has been cut, you need to fix it with the vent cap; You can do it by sheathing with screws.
5. Build the environment
After checking the vent cap, place the deck and begin building the environment. You need to make sure the space between the wood support and the fireplace is within the guidelines. Wood is a highly flammable material, so you must be especially careful when placing it together with items that could set it on fire.
6. Install the metal drywall
Be sure to cover all outside corners with a metal corner drywall trim. In this way, you can lay the drywall and settle the accounts according to the location and feasibility of the space. You may need to purchase a drywall screw gun or T-square to make proper adjustments.
7. Plaster
The type of plaster you use, premixed or self-mixed, depends on what you want to do. Plasters come in various textures, and we recommend using a premixed mix as it is less likely to have improper proportions. Try practicing in several places to become familiar with plastering so that you don’t end up with drywall that has an uneven texture and finish.
